Pengendalian Kualitas Produk Kopi Menggunakan Metode Seven Tools Dan Failure Mode And Effect Analysis (FMEA) Di UMKM Dharma Coffee

Aldimas Dafi Saputra; Andung Jati Nugroho

doi:10.59061/repit.v1i3.370

Authors

Aldimas Dafi Saputra Universitas Teknologi Yogyakarta
Andung Jati Nugroho Universitas Teknologi Yogyakarta

DOI:

https://doi.org/10.59061/repit.v1i3.370

Keywords:

Quality Control, Seven Tools, Failure Mode And Effect Analysis

Abstract

Umkm Dharma Coffee is a medium to lower business engaged in processing coffee beans into coffee powder. The problems that arise are defective products such as inappropriate weight and damaged packaging containers. From data from July to December 2022, with a total production volume of 2,760 pcs, there were 219 product defects, including 141 defective product defects and 78 damaged packaging container defects. Therefore, to reduce the number of product defects, it is necessary to support the company's management and production employees. The purpose of this research is to find out the causes of product defects using the Seven Tools method and statistically mapping the problems in order to see corrective actions that must be taken based on the factors that cause product defects using the Failure Mode And Analysis (FMEA) method. From the results of the SOD analysis, it was obtained that the highest RPN value was 36 in the damaged packaging container. The recommendations for improvement given are that companies must implement clear SOP, conduct job education and training for employees so that later they can maximize the production process in the company.

References

Ansyah, N. A., & Sulistiyowati, W. (2022). Analysis of Quality Control of Shrimp Crop Products with Seven Tools and FMEA Methods (Case Study: UD. Djaya Bersama). Procedia of Engineering and Life Science, 2(2).

Adwianoor, H. (2023). ANALISIS PERBAIKAN PENGENDALIAN KUALITAS PRODUK BESI AS ULIR DENGAN METODE SEVEN TOOL DAN FMEA (Studi Kasus: CV. Logam Karya) (Doctoral dissertation, Universitas Islam Kalimantan MAB).

Damaindra, M., & Cahyana, A. S. (2017). Peningkatan kualitas produk pada mesin produksi Nonwoven Spunbond dengan menggunakan metode seven tools dan FMEA. Spektrum Industri, 15(2), 245.

Dewangga, A., & Suseno, S. (2022). Analisa Pengendalian Kualitas Produksi Plywood Menggunakan Metode Seven Tools, Failure Mode And Effect Analysis (FMEA), Dan TRIZ. Jurnal Teknologi dan Manajemen Industri Terapan, 1(3), 243-253.

DEWI, L. H. (2020). PENGENDALIAN KUALITAS LINI PRODUK RENADINAC TABLET DENGAN METODE SEVEN TOOLS DAN METODE FMEA (Failure Mode Effect And Analysis) STUDI KASUS DI PT PRATAPA NIRMALA (FAHRENHEIT) (Doctoral dissertation, Universitas Mercu Buana Jakarta).

Firmansyah, M. J., & Nuruddin, M. (2022). Analisis Pengendalian Kualitas Produksi Pada PT. XYZ Menggunakan Metode Seven Tools Dan FMEA. SITEKIN: Jurnal Sains, Teknologi dan Industri, 20(1), 231-238.

Ishak, A., & Aura, D. (2020, November). Pengendalian Kualitas Produk Hairdryer dengan Metode Seven Tools. In Talenta Conference Series: Energy and Engineering (EE) (Vol. 3, No. 2).

Melinda, T., & Ginting, E. (2016). Identifikasi Kecacatan Coil Basah Dan Upaya Perbaikan Dengan Metode Seven Tools Dan Faulure Mode And Effect Analysis (FMEA) Di PT. XYZ Medan. Jurnal Sistem Teknik Industri, 18(2), 101-107.

Mulyati, D. S. (2015). Perbaikan pengendalian kualitas dengan menggunakan seven quality control tools dan metoda FMEA (failure Mode and Effects Analysis).

Noviora, D., & Imam, S. (2022, December). ANALISIS PENGENDALIAN KUALITAS KEMASAN X DENGAN MENGGUNAKAN METODE SEVEN TOOLS, FMEA, DAN ANALISIS 5W+ 1H (STUDI KASUS: PT XYZ). In PROCEEDING SEMINAR NASIONAL TEKNOLOGI CETAK DAN MEDIA KREATIF (TETAMEKRAF) (Vol. 1, No. 2, pp. 555-562).

Rohkma, A. N., & Aryanny, E. (2023). Analisa Tingkat Kecacatan Bata Beton Ringan Dengan Metode Seven Tools dan FMEA Di CV. XYZ-Mojokerto. Jurnal Kendali Teknik dan Sains, 1(3), 39-53.

Safitri, W., & Fahreza, D. M. (2023). The Analisis Product Defect dengan Metode Seven Tools dan FMEA. Jurnal Pelita Manajemen, 2(01), 1-12.

Sumarya, E. (2021). Pengendalian Kualitas Produk Pada Proses Produksi Air Minum Dalam Kemasan Botol 600 Ml Dengan Metode Failure Mode Efect Analysis (Fmea) Di Pt. Lmn Batam. PROFISIENSI: Jurnal Program Studi Teknik Industri, 9(1), 178-187.

Wijaya, B. S., & Andesta, D. (2021). Minimasi Kecacatan pada Produk Kemasan Kedelai Menggunakan Six Sigma, FMEA dan Seven Tools di PT. SATP. Jurnal Media Teknik Dan Sistem Industri, 5(2), 83-91.

Yovita, Y., Rahayu, S., & Megawati, V. (2019). Pengendalian Kualitas dengan Metode Seven Tools dan FMEA di CV. Babypro Jakarta. CALYPTRA, 7(2), 2827-2845.